Old Motifator threads are available in the Archive.
cliffxr
Total Posts: 23
Joined 12-04-2004 status: Regular |
Under File, I performed a Save All to capture my current settings with no issues. I’m using a known good USB that I’ve used with the Motif previously. When I try to load that same file, I get “Waveform Full” as an error message. Settings are Type: ALL, FL1: without sample, FL2: without sample, Load USR: USR, FL1: FL1, FL2: FL2. I have one 1024 Flashboard installed. I know it’s probably something simple, but I don’t mess with the File function often and have no clue what I’m doing wrong. Would appreciate some guidance. Thanks. I’ve gone back and tried Loading with FL 1: without sample and still get the same problem. |
cmayhle
Total Posts: 3116
Joined 10-05-2011 status: Guru |
First, review This Article if you haven’t done so for a while, especially the last third or so of it. When you SAVE without sample, you are still SAVING waveforms...the pointers or “containers” for the samples. So, it stands to reason that when you LOAD FL1:FL1 and FL2:FL2, you are actually re-LOADING the WAVEFORMS each time, even though you are not LOADING Samples (because you SAVED without sample). Set these LOAD options to FL1:None and FL2:None to LOAD neither samples nor WAVEFORMS (I know you only have FL1, the references to FL2 are rhetorical for the sake of clarity/consistency). You will want to clear out all of the duplicate WAVEFORMS you have on your Flash Board at some point. Since your FLASH board has a theoretical maximum of 2048 Waveforms, it seems like you have been stacking them up for a while now! |
cliffxr
Total Posts: 23
Joined 12-04-2004 status: Regular |
cmahyle, thanks for the quick response. Setting to None worked. Still not sure why. I’ve read the article awhile back and still don’t get it 100%. I need to go over it again a couple times. I also didn’t understand why I would need to clear out the duplicate waveforms (or even how they’re duplicated) on the Flash Board or even how I see them. |
cmayhle
Total Posts: 3116
Joined 10-05-2011 status: Guru |
Well, I guess you don’t need to clear out duplicate WAVEFORMS if you will not be needing to LOAD any new WAVEFORMS in the future! You can manage the Flash Expansion Module in UTILITY (see page 230 of the Motif XF Reference Manual). To paraphrase (or re-phrase) my post above per your questions: WAVEFORMS (from your FL1) get SAVED every time you SAVE an ALL File without sample. Those SAVED WAVEFORMS get re-LOADED (to your FL1) every time you LOAD FL1:FL1. |
cliffxr
Total Posts: 23
Joined 12-04-2004 status: Regular |
I obviously need to read up some more on Flash memory and Loading/Saving. Thanks again for getting me to an immediate solution! |
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
Perhaps this will clarify things a bit…
The “None” Load option for FL1/FL2 cmayhle pointed out (and as described in the support article) will prevent Waveform duplication. (That option isn’t mentioned in the XF Reference Manual because it was first available with OS version 1.10.) If the Waveform memory is almost full, using the “None” setting will prevent that memory from being filled and the error message appearing. However, the duplicate Waveforms should be removed or you’ll be limited in adding any more. |
cliffxr
Total Posts: 23
Joined 12-04-2004 status: Regular |
Thanks 5PinDIN, that helps clear it up a little more. |
cmayhle
Total Posts: 3116
Joined 10-05-2011 status: Guru |
This Thread has a lot of helpful information. Page 15 of the attached Supplementary Manual outlines an OS v1.10 update that allows removal of same-name WAVEFORMS from the Flash Board (one at a time). Alternatively, the John Melas Waveform Editor will elegantly allow you to remove duplicate WAVEFORMS from your Flash Board. From the Melas Waveform Editor Manual:
Remove Duplicate Waveforms
File Attachments
Supplementary Manual.pdf (File Size: 4171KB - Downloads: 344) |