Old Motifator threads are available in the Archive.
cseymour
Total Posts: 30
Joined 11-22-2009 status: Regular |
Hello,
Part 2:
Thanks,
|
cmayhle
Total Posts: 3116
Joined 10-05-2011 status: Guru |
As Bad_Mister says in This Thread, the XF will do what you tell it to do. You just need to be sure you are asking in the right way! Please go through the LOAD options in that thread carefully. You are doing something wrong in trying to LOAD 1BANK VOICES, it’s just not clear what, as we do not know your exact steps. To properly LOAD 1BANK, you must not only select that LOAD option (TYPE) as your choice, but you must specifically tell the machine which BANK you wish to LOAD (from your ALL File), as well as where (the BANK) you want it LOADED to. |
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
Samples/Waveforms on a flash module can’t be lost unless you intentionally delete them. They can’t be overwritten, and if you attempt to load more than the capacity of the module, the XF will prevent you from doing that.
As to your Part 1 question, déjà vu…
|
cseymour
Total Posts: 30
Joined 11-22-2009 status: Regular |
Hi 5 Pin,
|
cseymour
Total Posts: 30
Joined 11-22-2009 status: Regular |
I finally figured it out on the soundsets and installing both of them, and noone on here had it right.... Just wanted you to know. Anyone with the same problem feel free to PM me. I will gladly help.
|
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
Rather than just claiming that those of us who tried to help you are wrong, why not post your procedure here in this thread? That way, anyone who reads the thread will be informed, and the rest of us can compare your method with what was previously posted.
Â
I’d try to help, but lately it seems no good deed goes unpunished. |
cseymour
Total Posts: 30
Joined 11-22-2009 status: Regular |
Actually 5 pinDin, I just noticed your link under the deja vu comment, and following that link that is exactly what I did. Everything loaded up accepting for the performance files. I had to change to load performance and one by one add them to where I wanted them to go in the XF. So I was wrong you did have the right answer back then but saw it too late., any thoughts on that wave file loading to the FL1 Bank?
|
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
Thanks for clarifying the situation.
Â
In order to provide relevant advice, some details are needed…
Do you want the .WAVs to be installed on FL1 with or without association to a Voice? Are the files recordings of music, or are they samples of an instrument to be played? Are the files related to each other, as in a multi-sample of an instrument? The more you can tell us, the better. |
cseymour
Total Posts: 30
Joined 11-22-2009 status: Regular |
The wav files are 16 bit. They are of music for intros to songs so there are no associations to any voices. I would like them installed on the FL1 with the existing wav files that I installed years ago. Hope this helps.
|
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
OK, as long as the sample rate isn’t over 44.1kHz.
Â
That shouldn’t be a problem.
1) Select a Preset in Voice mode. (PRE1 A01 will do.)
Select any additional WAVs and load them as desired. |
cseymour
Total Posts: 30
Joined 11-22-2009 status: Regular |
Worked like a charm. Thank you… |