Old Motifator threads are available in the Archive.
benonemusic
Total Posts: 26
Joined 07-03-2015 status: Regular |
Yes. I was able to STORE the Multi and play it. The Rack XS froze when trying to navigate to a different Multi patch. Turning the Rack XS off and on did not help. In fact, the Rack XS remained stuck in startup while still connected to the computer. This is what also happened with the 80s Pop/Rock voices when using the Yamaha editor on both the Mac and PC as mentioned in my previous post. Only when I disconnected the computer and reloaded the factory patches was I able to remove the freezing problem. Ben |
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
Strange behavior. Apparently some “out of bounds” data is being sent to the Rack XS, and it’s not rejecting it. Since the Melas software was able to load the Voices from the 80’s Soundset without problems, it may be limiting what it sends to specific Parameter data. You might make sure that only “Current” is “On” when synchronizing the PC and Rack, leaving “Voice” (and possibly “Global") “Off”. I wonder if you could bulk dump the Multi (see pages 11 and 47 of the Owner’s Manual, concerning using [MULTI] button with [STORE]) before navigating away from it, or could the Melas Librarian capture “all”? Then perhaps the data could be sent “cleanly” back to the Rack XS, if necessary after a factory reset. I hesitate to suggest this, but you might be able to write down all the Parameter values of the Multi, and then hand enter them after a factory reset. On the other hand, it might be time to contact Yamaha. A .X0E file, created via a Yamaha XS Editor from data residing on a Motif XS, loaded to the Rack XS with Yamaha’s Rack XS Editor, shouldn’t cause problems. Yamaha has previously implied that the creator of the 80’s Soundset is at fault, but it’s hard for me to see it that way. |
benonemusic
Total Posts: 26
Joined 07-03-2015 status: Regular |
Thanks for these suggestions. I’ll try some of them when I have time later today, starting with leaving only “Current†on when synchronizing the Rack and computer. I’ll let you know what happens. I appreciate all of your amazing and patient help! |
benonemusic
Total Posts: 26
Joined 07-03-2015 status: Regular |
Good news! Turning off “Voice” on the autosync settings seems to do the trick. Even when “Global” is turned on the unit does not freeze. I’ve tried it numerous times and turned the unit on and off and everything seems okay. I guess there’s some issue with the voice data and the Yamaha editor.
|
stoneb3
Total Posts: 851
Joined 06-05-2011 status: Guru |
Good news indeed, congratulations. I’ve downloaded the driver and editor for a different MBP (v1.6.5), I will install it shortly and begin the process. Have you been able to name the stored multi? Stone |
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
Great! How about if I do the next 11 (A02~A12), making 12 in total? Hopefully Stone could do the remaining 12 (A13~A16 and B01~B08).
To address an earlier question Stone posed…
I’m not fond of posting this material, although it’s somewhat useless unless a person already has the library. Stone, what do you think? |
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
Stone, you posted while I was composing my previous message. Would you comment on what I suggested, etc? |
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
Ben, PM sent. |
stoneb3
Total Posts: 851
Joined 06-05-2011 status: Guru |
I think someone should have addressed this long ago. Say, either of the two parties involved.
The data is useless if posted here, as you mentioned. I’m game, and will do the second 12.
|
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
I must admit that I didn’t realize what some of the issues are with the Rack models. With respect to posting here, I’m going to send you a PM. I agree that there’s no need to check User 1. |
stoneb3
Total Posts: 851
Joined 06-05-2011 status: Guru |
Yeah, it brings back memories. Same with the ES. I did not get on with the file systems of either. I wanted to bulk via midi to the rack but what a pain to do. Good grief. I could have drove to MD and back. |
stoneb3
Total Posts: 851
Joined 06-05-2011 status: Guru |
. |
stoneb3
Total Posts: 851
Joined 06-05-2011 status: Guru |
Did you receive my reply? |
5pinDIN
Total Posts: 11891
Joined 09-16-2010 status: Legend |
Got it, and responded to it a short while ago. |
stoneb3
Total Posts: 851
Joined 06-05-2011 status: Guru |
Thanks.
|